Stabilizing a dog box?

A general forum for the discussion of hunting with beagles, guns, clothing and other equipment and just talking dawgs! (Tall tales on hunting allowed, but remember, first liar doesn't stand a chance)

Moderators: Pike Ridge Beagles, Aaron Bartlett

Post Reply
steve w
Posts: 539
Joined: Wed Aug 31, 2005 10:02 pm
Location: sw mi

Stabilizing a dog box?

Post by steve w »

How do you guys keep your dog boxes from sliding around? I bought a new truck with a plastic bed liner and it sure is slippery. Thanks in advance

Hill Top Beagles
Posts: 182
Joined: Fri Dec 10, 2010 8:00 pm

Re: Stabilizing a dog box?

Post by Hill Top Beagles »

I took a bed bolt out drilled hole in the bottom of box and put the bed bolt through the hole, makes them harder to steal.

BCBeagles
Posts: 5546
Joined: Tue Apr 07, 2009 6:27 am
Location: West Virginia

Re: Stabilizing a dog box?

Post by BCBeagles »

I have an Owens box, I put two decent size U bolts up on the front edge below the lid. Drilled them out and used washers on both sides. I attach my ratchet straps to these. It works great and looks nice. I have been asked many times if it came that way and I say, no one of my only decent ideas! LOL.

Good luck!

THUNDERHILL KENNEL
Posts: 7
Joined: Wed Dec 08, 2010 10:31 am

Re: Stabilizing a dog box?

Post by THUNDERHILL KENNEL »

Take 2 2by4's about 3 inches longer than length of box, fasten to bottom of box,drill 2 three-eight hole's through 2by4 and truck bed,either bolt down tight or just use bolts like hitch pin,easy to pull out...

User avatar
DIXIEDOG
Posts: 1174
Joined: Mon Jun 12, 2006 6:26 pm
Location: MAINE

Re: Stabilizing a dog box?

Post by DIXIEDOG »

I run 4 ratchet straps from the lift handles to the bed tie downs...one in each corner. Then I run a Master cable lock through one tiedown and the handle to prevent somebody from backing up to my truck and sliding it into theirs. I don't want to drill holes through the box or I'd bolt it down through my bed hold down bolts as well.

poorboy kennels
Posts: 118
Joined: Sat Oct 29, 2011 9:41 am

Re: Stabilizing a dog box?

Post by poorboy kennels »

Rubber mat and chained it in

20guage92
Posts: 161
Joined: Mon Feb 13, 2012 2:36 pm

Re: Stabilizing a dog box?

Post by 20guage92 »

put 2by4 framed box behind the dog box 1, 24inch 2by4 in frunt of dog box.to keep it from hiting tailgate.

east80kennels
Posts: 798
Joined: Mon Jan 30, 2012 5:10 pm

Re: Stabilizing a dog box?

Post by east80kennels »

get you some mining belt, or a rubber mat.

yoteslayer
Posts: 364
Joined: Wed Nov 16, 2011 10:42 pm
Location: New Hampton, Ia

Re: Stabilizing a dog box?

Post by yoteslayer »

I have a homemade peice of junk box that I made just wide enough to wedge between the wheel wells and then I have a strap that holds it in place at the tailgate end. I dont have to worry about it getting stolen, I have exactly $4 invested in it....

pilotknob
Posts: 381
Joined: Tue Jan 10, 2012 3:20 pm
Location: central ky

Re: Stabilizing a dog box?

Post by pilotknob »

I layed a 2x6 down flat between the box and the tailgate.Then I shoved the box tight against the 2x6 and tailgate.Then I measured between the back of the box and the inside of the bed,Then made a 2x6 frame to fill the hole about as wide as the box.This stops the latches from ever hitting the tailgate and the frame is handy to put stuff in.

Post Reply