Measuring Stand

mayberry1 · Post by **mayberry1** » Mon Feb 06, 2006 6:35 pm

I was just wandering if anyone could tell me where i could buy a measuring stand. The kind used in AKC trials.

Chris Spall · Post by **Chris Spall** » Mon Feb 06, 2006 6:43 pm

I make measuring stands. Price is $85 and that includes shipping and handling. email me and I will send you a couple of pictures of the stand that I make.

mccall · Post by **mccall** » Mon Feb 06, 2006 6:46 pm

i would not get a AKC measuring stand they usually are a couple of inches off

dawgydawg67 · Post by **dawgydawg67** » Wed Feb 08, 2006 12:50 pm

I have one from Chris, I highly recommend it. Good quality and good price. Bob Dawes

TC · Post by TC » Wed Feb 08, 2006 1:10 pm

Our Club ordered one from Chris REAL GOOD quality and craftsmanship Would highly Recomend him + they meet AKC and UKC standards!!!

TOPGUN · Post by **TOPGUN** » Wed Feb 08, 2006 4:14 pm

Chris, I want to buy one of your dtands for our club. I don`t see your email. Drop me a PM with your email or a phone # and I`ll be in touch. Thanks Kevin

Honey Pot Hounds · Post by **Honey Pot Hounds** » Wed Feb 08, 2006 4:42 pm

There is also a fellow that makes very nice wickets for a fair price here:
http://www.ezwicket.com/

He'll put your kennel name on it for free too.

TC · Post by TC » Thu Feb 09, 2006 1:07 am

Cindy.
Someone Will correct me if i am Wrong i am Sure LOl
BUT The wicket canntot be used in a AKC or UKC Field trials To much margin for error LOL
The stands used for the trials must be AKC or UKC approved and have certain Qualifications that they must adhere to. I will see if i can find the requirements again and post them.
We were told by an AKC rep at our Seminar that the WICKET could not be used at a Sanctioned trial!

3-E A measuring stand made entirely of metal and
meeting the requirements of The American Kennel
Club must be used for all measuring at field trials
including Official Measurement. The contact bar shall
have a smooth edge, and there shall be no markings
or calibrations on the measuring stand or stick. Any
calibrations shall be on a separate part or sleeve, so
that the stick is set and locked before the measurers
know the hound’s height in inches. The calibrations
must be checked with a gauge or rule for each class.
The contact bar shall be loosely placed across the
shoulder blades at the highest point, the hound standing
in a naturally alert position with the head up but
not stretched upward and with its feet well under it
and forelegs vertical on a flat, level board with a nonslip
surface, placed at floor or ground level. The contact
bar must never be set in advance at a specified
height, but may only be set at the height of the particular
hound being measured. The hound shall be
posed for measurement by the measurers, and once
the reading has been made, no additional measurements
shall be taken.

Chris Spall · Post by **Chris Spall** » Fri Feb 10, 2006 8:16 pm

Thanks everyone for your support. I try to make them the best that I can.

WhiteCreekBeagles · Post by **WhiteCreekBeagles** » Mon Nov 22, 2010 12:58 am

Chris, Will You send me a couple pictures of the measuring stand that you make along with the current price. Thanks

chapkosbeagles · Post by **chapkosbeagles** » Mon Nov 22, 2010 7:03 am

yeah i need one of them stands too you know the one that is a cuple inches off. i am really looking to get some of these dogs in the trials but all the rabbit catchers keep going 16 inches

ace really dont like to stand any more

The American Beagler Forum

Measuring Stand

Measuring Stand

Measuring stand

stand

measureing stands For Sale

Re: Measuring Stand

Re: Measuring Stand